User Contributed MET/CAL PROCEDURE ============================================================================= INSTRUMENT: PM 2535 (Calibration) DATE: 04-Aug-93 AUTHOR: User Contributed REVISION: 1.0 ADJUSTMENT THRESHOLD: 90% NUMBER OF TESTS: 1 NUMBER OF LINES: 206 CONFIGURATION: Fluke 5700A ============================================================================= STEP FSC RANGE NOMINAL TOLERANCE MOD1 MOD2 3 4 CON 1.001 ASK- R N P M F W 1.002 HEAD GENERAL REQUIREMENT 1.003 DISP All UUTs require a minimum warm-up period of 30 minutes. 1.003 DISP Please connect IEEE cable to UUT from ATE. 1.003 DISP 1.003 DISP Connect a banana cable to UUT - V-OHM and O inputs 1.003 DISP and the 5700A CALIBRATOR Output. 1.004 IEEE INIT[10] 1.005 HEAD UUT CURRENT FIRMWARE REVISION CHECK 1.006 IEEE ID ?[I$][10] 1.007 DISP UUT software revision [27][91]7m[MEM2][27][91]m 1.007 DISP 1.007 DISP Enable the Calibration Mode by pressing the CAL and 1.007 DISP RESET switchs at the same time and release the 1.007 DISP RESET switch before releasing the CAL switch. 1.008 HEAD {DC VOLTAGE Calibration - 300mV Range} 1.009 IEEE [T0]CAL ON,VDC 300E-3[10] 1.010 5700 0V S 2W 1.011 IEEE [T0]X1[I][10] 1.012 5700 300mV S 2W 1.013 IEEE [T0]X1[I][10] 1.014 MEM* 1000 1.015 5700 -300mV S 2W 1.016 IEEE [T0]X1[I][10] 1.017 MEM* 1000 1.018 HEAD {DC VOLTAGE Calibration - 3V Range} 1.019 IEEE [T0]CAL ON,VDC 3E0[10] 1.020 5700 0V S 2W 1.021 IEEE [T0]X1[I][10] 1.022 5700 3V S 2W 1.023 IEEE [T0]X1[I][10] 1.024 5700 -3V S 2W 1.025 IEEE [T0]X1[I][10] 1.026 HEAD {DC VOLTAGE Calibration - 30V Range} 1.027 IEEE [T0]CAL ON,VDC 30E0[10] 1.028 5700 0V S 2W 1.029 IEEE [T0]X1[I][10] 1.030 5700 30V S 2W 1.031 IEEE [T0]X1[I][10] 1.032 5700 -30V S 2W 1.033 IEEE [T0]X1[I][10] 1.034 HEAD {DC VOLTAGE Calibration - 300V Range} 1.035 IEEE [T0]CAL ON,VDC 300E0[10] 1.036 5700 0V S 2W 1.037 IEEE [T0]X1[I][10] 1.038 5700 300V S 2W 1.039 IEEE [T0]X1[I][10] 1.040 5700 -300V S 2W 1.041 IEEE [T0]X1[I][10] 1.042 HEAD {AC VOLTAGE Calibration - 300mV Range} 1.043 IEEE [T0]CAL ON,VAC 300E-3[10] 1.044 5700 300mV 400H S 2W 1.045 IEEE [T0]X1[I][10] 1.046 MEM* 1000 1.047 HEAD {AC VOLTAGE Calibration - 3V Range} 1.048 IEEE [T0]CAL ON,VAC 3E0[10] 1.049 5700 3V 400H S 2W 1.050 IEEE [T0]X1[I][10] 1.051 HEAD {AC VOLTAGE Calibration - 30V Range} 1.052 IEEE [T0]CAL ON,VAC 30E0[10] 1.053 5700 30V 400H S 2W 1.054 IEEE [T0]X1[I][10] 1.055 HEAD {AC VOLTAGE Calibration - 300V Range} 1.056 IEEE [T0]CAL ON,VAC 300E0[10] 1.057 5700 300V 400H S 2W 1.058 IEEE [T0]X1[I][10] 1.059 5700 * S 1.060 HEAD {DC CURRENT Calibration - Setup} 1.061 DISP Connect a banana cable to UUT - A and O inputs 1.061 DISP and the 5700A CALIBRATOR Output. 1.062 HEAD {DC CURRENT Calibration - 30mA Range} 1.063 IEEE [T0]CAL ON,IDC 30E-3[10] 1.064 5700 0mA S 2W 1.065 IEEE [T0]X1[I][10] 1.066 5700 30mA S 2W 1.067 IEEE [T0]X1[I][10] 1.068 MEM* 1000 1.069 5700 -30mA S 2W 1.070 IEEE [T0]X1[I][10] 1.071 MEM* 1000 1.072 HEAD {DC CURRENT Calibration - 3A Range} 1.073 IEEE [T0]CAL ON,IDC 3E0[10] 1.074 5700 0A S 2W 1.075 IEEE [T0]X1[I][10] 1.076 5700 2A S 2W 1.077 IEEE [T0]X1[I][10] 1.078 5700 -2A S 2W 1.079 IEEE [T0]X1[I][10] 1.080 5700 * S 1.081 HEAD {AC CURRENT Calibration - 30mA Range} 1.082 IEEE [T0]CAL ON,IAC 30E-3[10] 1.083 5700 30mA 400H S 2W 1.084 IEEE [T0]X1[I][10] 1.085 MEM* 1000 1.086 HEAD {AC CURRENT Calibration - 3A Range} 1.087 IEEE [T0]CAL ON,IAC 3E0[10] 1.088 5700 2A 400H S 2W 1.089 IEEE [T0]X1[I][10] 1.090 5700 * S 1.091 HEAD {2W OHMS Calibration - Precal} - SHORT 1.092 IEEE [T0]CAL ON,FNC RTW[10] 1.093 DISP Connect a banana cable to UUT - V-OHM and O inputs 1.093 DISP and the FTE 1752 Resistance Standard - ZERO output. 1.094 IEEE [T0]X1[I][10] 1.095 HEAD 2W OHMS Calibration - Precal - OPEN 1.096 DISP Disconnect the banana cable from the 1.096 DISP UUT - V-OHM and O inputs 1.097 IEEE [T0]X1[I][10] 1.098 HEAD 2W OHMS Calibration - Precal - 30Mę 1.099 DISP Connect the 30 Mę standard to the 1.099 DISP UUT - V-OHM and O inputs 1.100 IEEE [T0]X1[I][10] 1.101 HEAD 2W OHMS Calibration - 3Kę Range 1.102 IEEE [T0]CAL ON,RTW 3E3[10] 1.103 DISP Connect a banana cable to UUT - V-OHM and O inputs 1.103 DISP and the FTE 1752 Resistance Standard - ZERO output. 1.104 IEEE [T0]X1[I][10] 1.105 DISP Connect a banana cable to UUT - V-OHM and O inputs 1.105 DISP and the FTE 1752 Resistance Standard - 3Kę output. 1.106 IEEE [T0]X1[I][10] 1.107 HEAD 2W OHMS Calibration - 30Kę Range 1.108 IEEE [T0]CAL ON,RTW 30E3[10] 1.109 DISP Connect a banana cable to UUT - V-OHM and O inputs 1.109 DISP and the FTE 1752 Resistance Standard - ZERO output. 1.110 IEEE [T0]X1[I][10] 1.111 DISP Connect a banana cable to UUT - V-OHM and O inputs 1.111 DISP and the FTE 1752 Resistance Standard - 30Kę output. 1.112 IEEE [T0]X1[I][10] 1.113 HEAD 2W OHMS Calibration - 300Kę Range 1.114 IEEE [T0]CAL ON,RTW 300E3[10] 1.115 DISP Connect a banana cable to UUT - V-OHM and O inputs 1.115 DISP and the FTE 1752 Resistance Standard - ZERO output. 1.116 IEEE [T0]X1[I][10] 1.117 DISP Connect a banana cable to UUT - V-OHM and O inputs 1.117 DISP and the FTE 1752 Resistance Standard - 300Kę output. 1.118 IEEE [T0]X1[I][10] 1.119 HEAD 2W OHMS Calibration - 3Mę Range 1.120 IEEE [T0]CAL ON,RTW 3E6[10] 1.121 DISP Connect a banana cable to UUT - V-OHM and O inputs 1.121 DISP and the FTE 1752 Resistance Standard - ZERO output. 1.122 IEEE [T0]X1[I][10] 1.123 DISP Connect a banana cable to UUT - V-OHM and O inputs 1.123 DISP and the FTE 1752 Resistance Standard - 3Mę output. 1.124 IEEE [T0]X1[I][10] 1.125 HEAD 2W OHMS Calibration - 30Mę Range 1.126 IEEE [T0]CAL ON,RTW 30E6[10] 1.127 DISP Connect a banana cable to UUT - V-OHM and O inputs 1.127 DISP and the FTE 1752 Resistance Standard - ZERO output. 1.128 IEEE [T0]X1[I][10] 1.129 DISP Connect the 30Mę standard to the V-OHM and O inputs 1.130 IEEE [T0]X1[I][10] 1.131 HEAD 2W OHMS Calibration - 300Mę Range 1.132 IEEE [T0]CAL ON,RTW 300E6[10] 1.133 DISP Connect a banana cable to UUT - V-OHM and O inputs 1.133 DISP and the FTE 1752 Resistance Standard - ZERO output. 1.134 IEEE [T0]X1[I][10] 1.135 DISP Connect the 300Mę standard to the V-OHM and O inputs 1.136 IEEE [T0]X1[I][10] 1.137 HEAD 4W OHMS Calibration - 3Kę Range 1.138 IEEE [T0]CAL ON,RFW 3E3[10] 1.139 DISP Connect a 4 Wire Test cable to UUT - PROBE input. 1.139 DISP and the FTE 1752 Resistance Standard - ZERO output. 1.140 IEEE [T0]X1[I][10] 1.141 DISP Connect a 4 Wire Test cable to UUT - PROBE input. 1.141 DISP and the FTE 1752 Resistance Standard - 3Kę output. 1.142 IEEE [T0]X1[I][10] 1.143 HEAD 4W OHMS Calibration - 30Kę Range 1.144 IEEE [T0]CAL ON,RFW 30E3[10] 1.145 DISP Connect a 4 Wire Test cable to UUT - PROBE input. 1.145 DISP and the FTE 1752 Resistance Standard - ZERO output. 1.146 IEEE [T0]X1[I][10] 1.147 DISP Connect a 4 Wire Test cable to UUT - PROBE input. 1.147 DISP and the FTE 1752 Resistance Standard - 30Kę output. 1.148 IEEE [T0]X1[I][10] 1.149 HEAD 4W OHMS Calibration - 300Kę Range 1.150 IEEE [T0]CAL ON,RFW 300E3[10] 1.151 DISP Connect a 4 Wire Test cable to UUT - PROBE input. 1.151 DISP and the FTE 1752 Resistance Standard - ZERO output. 1.152 IEEE [T0]X1[I][10] 1.153 DISP Connect a 4 Wire Test cable to UUT - PROBE input. 1.153 DISP and the FTE 1752 Resistance Standard - 300Kę output. 1.154 IEEE [T0]X1[I][10] 1.155 HEAD 4W OHMS Calibration - 3Mę Range 1.156 IEEE [T0]CAL ON,RFW 3E6[10] 1.157 DISP Connect a 4 Wire Test cable to UUT - PROBE input. 1.157 DISP and the FTE 1752 Resistance Standard - ZERO output. 1.158 IEEE [T0]X1[I][10] 1.159 DISP Connect a 4 Wire Test cable to UUT - PROBE input. 1.159 DISP and the FTE 1752 Resistance Standard - 3Mę output. 1.160 IEEE [T0]X1[I][10] 1.161 IEEE CAL OFF[GTL] 1.162 HEAD Store CALIBRATION Constants 1.163 DISP Disable the Calibration Mode by pressing the Reset Sw. 1.164 HEAD THE END